If you register, you can do a lot more. And become an active part of our growing community. You'll have access to hidden forums, and enjoy the ability of replying and starting conversations.

Retyring

Discussion in 'Locomotive Engineering M.I.C' started by metalastic, May 20, 2010.

  1. metalastic

    metalastic New Member

    Joined:
    Jul 17, 2009
    Messages:
    10
    Likes Received:
    0
    Gender:
    Male
    Occupation:
    Baker
    Location:
    Tasmania
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Looking at various societies web sites & youtube videos- when retyring wheelsets I notice that it seems to be S O P in the UK to take a small clean up cut off the wheel centers. From my extremely limited experience, this was not par for the course here in Australia or the USA unless there was some damage to the wheel centres such as a slipped tyre etc.

    Can anyone advise if this is a normal practice and if so why? I would have thought that provided no damage had occured, the wheel centres would be fine as is.


    Ian
     
  2. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I don't understand why, either, but it seems to be the trend with some suppliers. The last lot of tyres I had done (by Bagguley Engineering) certainly weren't, though.
     
  3. 1472

    1472 Well-Known Member

    Joined:
    Aug 26, 2008
    Messages:
    1,898
    Likes Received:
    2,517
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    This may be done because after service & old tyre removal the wheel centre may no longer be round. This is caused by the shape of a steam loco wheel to allow for a crankpin which may cause different stresses around the wheel circumference. Clearly for accurate measurement of the old centre & new tyre to the tolerances required for fitting roundness is essential.
     
  4. class8mikado

    class8mikado Part of the furniture

    Joined:
    Jun 1, 2009
    Messages:
    3,609
    Likes Received:
    1,438
    Occupation:
    Print Estimator/ Repository of Useless Informatio.
    Location:
    Bingley W.Yorks.
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Am i right in thinking that a wheel size ie 6ft 2 inches is the diameter of the wheel without tyres on, and with new tyres the diameter could be another 5-6 inches (including Flange)....
     
  5. John Webb

    John Webb Member

    Joined:
    Mar 2, 2010
    Messages:
    501
    Likes Received:
    86
    Occupation:
    Retired
    Location:
    St Albans, Herts
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    The diameter quoted in books and diagrams of a loco wheel is the diameter across the tread of the wheel (ie wheel centre section plus tyre) and is what is used to calculate the nominal tractive effort.
     
  6. SMIFF

    SMIFF New Member

    Joined:
    Oct 10, 2010
    Messages:
    43
    Likes Received:
    0
    It was the practice in the BRML Eastleigh Works Wheel shop on all tyred wheelsets, including coach wheels. The slang term was "Topping" them.
     
  7. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    The variation in wheel diameter due to tyres being turned can have quite an effect on a locos drawbar pull as can the variation in cylinder size as they are bored out to rectify wear. A black 5 with tyres at minimum diameter and cylinders bored out to the maximum is about 10% stronger than a Black 5 that is to design spec.
     
  8. class8mikado

    class8mikado Part of the furniture

    Joined:
    Jun 1, 2009
    Messages:
    3,609
    Likes Received:
    1,438
    Occupation:
    Print Estimator/ Repository of Useless Informatio.
    Location:
    Bingley W.Yorks.
    Heritage Railway Volunteer:
    No I do not currently volunteer
    So its the rail to centre of axle x 2... and the flange typically another inch... ?
     
  9. SMIFF

    SMIFF New Member

    Joined:
    Oct 10, 2010
    Messages:
    43
    Likes Received:
    0
    Don't include the flange.
     
  10. class8mikado

    class8mikado Part of the furniture

    Joined:
    Jun 1, 2009
    Messages:
    3,609
    Likes Received:
    1,438
    Occupation:
    Print Estimator/ Repository of Useless Informatio.
    Location:
    Bingley W.Yorks.
    Heritage Railway Volunteer:
    No I do not currently volunteer
    errrrrrr..... ok.
     

Share This Page