If you register, you can do a lot more. And become an active part of our growing community. You'll have access to hidden forums, and enjoy the ability of replying and starting conversations.

Manning Wardles "YEO" and "EXE" new-build

Discussion in 'Narrow Gauge Railways' started by Old Kent Biker, Aug 15, 2018.

  1. pmh_74

    pmh_74 Well-Known Member

    Joined:
    Jan 28, 2009
    Messages:
    2,216
    Likes Received:
    1,456
    You could, in theory, take the whole wheelset out, rotate it 180 degrees and pop it back in the other way round, to even up the wear (assuming that for whatever reason you didn't want to rotate the whole vehicle 180 degrees). I'm aware of one loco group which used to do that with their trailing wheelset.
     
  2. Bikermike

    Bikermike Well-Known Member

    Joined:
    Mar 11, 2020
    Messages:
    1,442
    Likes Received:
    1,595
    Gender:
    Male
    Location:
    Thameslink territory
    Heritage Railway Volunteer:
    No I do not currently volunteer
    I've seen it done with a slick on a racing bike, but not elsewhere...

    Funny, I was thinking it must be Wrong, but then railway engines go both ways equally, so it has to work both ways. I wonder if swapping the bearings round would be the issue.

    Obviously a turntable would be the obvious thing - assuming the line has one.
     
  3. 30854

    30854 Resident of Nat Pres

    Joined:
    Mar 8, 2017
    Messages:
    12,172
    Likes Received:
    11,493
    Gender:
    Male
    Occupation:
    Retired
    Location:
    Brighton&Hove
    Heritage Railway Volunteer:
    No I do not currently volunteer
    In light of the L&B's Pilton turntable, now back in L&B hands, astoundingly on topic!
     
  4. bantamd14

    bantamd14 New Member

    Joined:
    Jan 21, 2017
    Messages:
    131
    Likes Received:
    91
    Gender:
    Male
    Location:
    Stafford
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Surely the 'quartering' would be out if you turned a 'cranked' wheelset by 180 degrees?
     
  5. marshall5

    marshall5 Well-Known Member

    Joined:
    Oct 26, 2010
    Messages:
    2,375
    Likes Received:
    3,981
    Location:
    i.o.m
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Don't think so..... If a loco is 'right hand leading' it will remain so if you turn the wheelset round 180 degrees.
    Ray.
     
    pmh_74 likes this.
  6. Wayne

    Wayne New Member

    Joined:
    Dec 8, 2008
    Messages:
    195
    Likes Received:
    506
    Quite a lot of mainline vehicles do not have tyres anymore. Once they get down to their final cut, wheelset change. Class 66 for example.
     
  7. pmh_74

    pmh_74 Well-Known Member

    Joined:
    Jan 28, 2009
    Messages:
    2,216
    Likes Received:
    1,456
    Exactly. The loco concerned was in regular main line use at the time and I understand it saved them a small fortune in tyres.


    Sent from my iPhone using Tapatalk
     
  8. David Humphreys

    David Humphreys New Member

    Joined:
    Apr 11, 2011
    Messages:
    99
    Likes Received:
    306
    Gender:
    Male
    Occupation:
    Managing Director
    Location:
    Boosbeck, Saltburn by the Sea
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    As agents for Ringrollers, I received a letter from them re their current problems. Covid and world supply of steel.



    The effects of the COVID-19 pandemic are still felt throughout the world economy, and it drastically
    changed the business landscape as well as the way we do business. As a company, Naledi Ringrollers
    was also affected, and our shortcomings were identified. The war in the Ukraine put even more emphasis
    on areas for improvement.
    We, at Naledi Ringrollers are moving forward from the lessons learned and have put measures in place
    to prevent and repair damages that were done by COVID-19. Our steel supply chain was also impacted
    negatively due to production and shipping delays. Full recovery of our input material supply chain is
    expected within the next 3-4 months.
    Customer service is still of high priority and therefore the advantage of a local office in Europe was
    recognised to ensure that we stay ahead of European market developments. With our strategic partners
    in Europe we are now in the process of establishing an office in Europe. We are expecting our new and
    existing customers to experience true value through our pooled competencies. The full details of this
    exciting development will be presented at InnoTrans in September 2022.
    With excitement we are looking forward at what the future holds.
     
  9. mikehartuk

    mikehartuk New Member

    Joined:
    Jun 29, 2007
    Messages:
    91
    Likes Received:
    441
    Gender:
    Male
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    To help dispel current myths about the supply of tyres for loco and rolling stock wheels.

    For some years my company Railway Wheelset & Brake Ltd have been the UK distributor of tyres manufactured in Germany to the UK requirements of British Standard 5892 Part 4 ‘Specification for Forged & Rolled Tyres’.

    RWB Ltd supply significant qualities of tyres to various users in the UK. Delivery as normally 12/14 weeks from order on the full range from the smallest narrow gauge to largest mainline pacific tyre. Supplied either as rolled, semi machined or fully finished.

    Website is at:

    https://www.railwaywheelset.co.uk/

    Hope that helps

    Thanks

    Mike Hart
     
    Last edited: May 11, 2022
    brmp201, weltrol, Mrcow and 6 others like this.
  10. Cosmo Bonsor

    Cosmo Bonsor Member

    Joined:
    Dec 10, 2014
    Messages:
    221
    Likes Received:
    500
    Gender:
    Male
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    If there are eccentrics on the axle for Stephenson's gear, the engine will go in the opposite direction to the one selected by the reverser.
    Seen it done...
     
    Dag Bonnedal likes this.
  11. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Not sure that's right. The eccentrics are placed relative to the crankpin at 90 degrees either side (ignoring angular advance for lap and lead) and the relationship will remain the same if you turn the axle through 180 degrees. If you go from open eccentric rods to crossed eccentric rods by putting the eccentric rod on the wrong eccentric strap, that will happen but not simply putting the wheelset in the wrong way round and attaching the eccentric rod to the correct strap.
    I think.:)
     
  12. Mark Thompson

    Mark Thompson Well-Known Member

    Joined:
    Sep 10, 2017
    Messages:
    1,429
    Likes Received:
    3,559
    Gender:
    Male
    Location:
    E sussex
    Heritage Railway Volunteer:
    No I do not currently volunteer
    There's a picture in the latest Trust magazine of the pony truck wheels now fully machined and profiled, and very tidy they look, too. Incidentally, does anyone know the reason for the blue/ green painting of the cylinder castings? Is it to make LH/RH easily identifiable, or something else entirely?
     
  13. Cosmo Bonsor

    Cosmo Bonsor Member

    Joined:
    Dec 10, 2014
    Messages:
    221
    Likes Received:
    500
    Gender:
    Male
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Not to get into a blah about it, but I have seen this very thing happen.
    Engine re-wheeled, put into gear, shot off in the unexpected direction.
    Wheelset taken out, turned round,all good.
     
    paullad1984 and Steve like this.
  14. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I'm sure that Tom or some other learned person on here will happily adjudicate. I too have experienced a steam engine going backwards instead of forwards when put into foregear. In my case it was a steam crane and the simple reason was that the eccentric rods had been attached to the wrong end of the expansion links and easily rectified. I've heard of it happening with other locos too, so it is far from a unique event.
    Whilst on the subject, link valve gears are usually arranged so that the link is dropped to put it into foregear but it doesn't have to be. With MW1210 'Sir Berkeley' the links are lifted for foregear. In this condition the it is said to have crossed eccentric rods and the gear gives maximum lead in full gear and not mid gear. Looking at photos of Sharpthorn, I suspect this loco is similarly laid out.
     
  15. Jamessquared

    Jamessquared Nat Pres stalwart

    Joined:
    Mar 8, 2008
    Messages:
    26,100
    Likes Received:
    57,414
    Location:
    LBSC 215
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I think the illustrious Chairman of the SER is better versed than me in such matters!

    That said, I’ve a vague memory of someone mentioning similar with Baxter. Conceivably the “folded in half” nature of the valve gear presents another opportunity to get things muddled on reassembly - but it’s late, and I’ve been up since silly o’clock, so one to ponder another day!

    Tom
     
  16. ilvaporista

    ilvaporista Part of the furniture

    Joined:
    Jan 16, 2006
    Messages:
    4,240
    Likes Received:
    5,291
    Gender:
    Male
    Occupation:
    C.Eng
    Location:
    On the 45th!
    I don't know about eccentrics in full size. Having done this in miniature it depends on how the valve gear is set up. I think if the eccentrics are a mirror image then it is possible to rotate the axle. If the eccentrics are arranged with the same one leading on both sides then you reverse the direction. It was a few years ago now so I may have mixed up which way round it was. However easy to fix in 5".
     
    Last edited: May 15, 2022
    Steve likes this.
  17. meeee

    meeee Member

    Joined:
    Mar 28, 2006
    Messages:
    864
    Likes Received:
    1,319
    It was to identify which loco they were for. There was also a red cylinder casting for Lyd.
    Tim
     
    Mark Thompson likes this.
  18. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    You're not wrong and, having thought about how rotating the wheelset could cause the loco to go in reverse, this was the conclusion I had come to. All wheelsets I've had dealings with have had mirror image eccentrics but I'm sure that there will be ones out there with non-mirror image eccentrics, though as there is nothing fundamentally wrong with that arrangement.
     
    Chris86 likes this.
  19. brmp201

    brmp201 Member

    Joined:
    May 18, 2010
    Messages:
    558
    Likes Received:
    771
    Gender:
    Male
    Occupation:
    IT Director
    Location:
    Surrey, UK
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Latest update from the 762 Club:

     
  20. Flying Phil

    Flying Phil Part of the furniture

    Joined:
    Dec 10, 2018
    Messages:
    2,696
    Likes Received:
    5,500
    Gender:
    Male
    Location:
    Leicestershire
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Good to read about progress from the 762 club. I am slightly puzzled about building two identical locomotives on different sites, I would have thought it slightly cheaper to have them together and share tooling/expertise?
     
    Small Prairie and H Cloutt like this.

Share This Page