If you register, you can do a lot more. And become an active part of our growing community. You'll have access to hidden forums, and enjoy the ability of replying and starting conversations.

Garratts - Why Not Cab Forward

Discussion in 'Steam Traction' started by johnofwessex, Jun 2, 2019.

  1. peckett

    peckett Member

    Joined:
    Sep 26, 2006
    Messages:
    726
    Likes Received:
    549
    What's the difference to buffering up to a train needing banking ,and buffering up to a train in sidings waiting for dispatch.? Surly it was the guards job to watch out ,the same as in sidings.
     
  2. peckett

    peckett Member

    Joined:
    Sep 26, 2006
    Messages:
    726
    Likes Received:
    549
     

    Attached Files:

    andrewshimmin likes this.
  3. peckett

    peckett Member

    Joined:
    Sep 26, 2006
    Messages:
    726
    Likes Received:
    549
    Please click on,, Click to Expanded ,to see reply above.
     
    Last edited: Dec 15, 2020
  4. LMS2968

    LMS2968 Part of the furniture

    Joined:
    Sep 1, 2006
    Messages:
    2,987
    Likes Received:
    5,084
    Gender:
    Male
    Occupation:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Location:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    It isn't the same thing: the guard - or shunter - would be on the ground in a siding but I don't think he would be when buffering up a banking engine. But Garratts had a few distinct problems: the two ends were a long way apart with a lot of (high volume) pipework between them. These had to be filled with steam (or possibly vacuum created; I'm not sure of the LNER Garratt's braking system), which took time. It would not therefore respond quickly when the driver realised his position, and it was easy to misjudge the braking distance required. The LMS Garratts had the same issues, and broken couplings and torn out headstocks were far from unknown. They of course were not used for banking nor worked passenger trains.

    The Garratt first arrived at Bromsgrove with its chimney to the bank, but was soon turned specifically because of the problems in buffering up. It didn't solve the time lag but did make the distance easier to judge.
     
    jnc, andrewshimmin, 35B and 3 others like this.
  5. 240P15

    240P15 Well-Known Member

    Joined:
    Dec 1, 2017
    Messages:
    1,598
    Likes Received:
    1,588
    Gender:
    Male
    Location:
    Norway
    Heritage Railway Volunteer:
    No I do not currently volunteer

    Fantastic photos! Thank you very much Dag Bonnedal! :)

    Another nice looking french Beyer Garrat the "sister engine " CFA 231-132 AT . Must have been a lovely sight in the grey P.O. colour scheme and black outlinings when delivered. https://upload.wikimedia.org/wikipedia/commons/thumb/b/b9/CFA_231+132_AT_1.jpg/800px-CFA_231+132_AT_1.jpg

    Knut:)
     
    andrewshimmin and Dag Bonnedal like this.
  6. Chris86

    Chris86 Well-Known Member

    Joined:
    Oct 31, 2011
    Messages:
    1,328
    Likes Received:
    1,315
    Occupation:
    Safety, Technical and Offroad Driver Trainer
    Location:
    South Yorkshore
    Heritage Railway Volunteer:
    No I do not currently volunteer
    I have always wondered if the Garratts were particularly difficult to handle for this very reason (lag time in response to controls)- also with the length of pipework would it have made them very liable to priming?

    The other thing that struck me from a post elsewhere on the forum was the implication of having one regulator controlling both engines, meaning if one engine slips the other can be starved of steam to an extent?

    Regards

    Chris
     
  7. peckett

    peckett Member

    Joined:
    Sep 26, 2006
    Messages:
    726
    Likes Received:
    549
     

    Attached Files:

    Last edited: Dec 15, 2020
    Bluenosejohn, LMS2968 and 240P15 like this.
  8. D6332found

    D6332found Member

    Joined:
    Dec 3, 2016
    Messages:
    361
    Likes Received:
    179
    Gender:
    Male
    Location:
    Dinting
    Heritage Railway Volunteer:
    No I do not currently volunteer
    I think Gresley's monster was periodically turned for equalising wheel wear. It did haul a passenger train once, so "new build anyone?"
     
  9. LMS2968

    LMS2968 Part of the furniture

    Joined:
    Sep 1, 2006
    Messages:
    2,987
    Likes Received:
    5,084
    Gender:
    Male
    Occupation:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Location:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    So did an LMS version, 4999, as a test. It failed with a hot box at Leicester and had to come off, and it was never tried again.
     
    Richard Roper likes this.
  10. peckett

    peckett Member

    Joined:
    Sep 26, 2006
    Messages:
    726
    Likes Received:
    549
     

    Attached Files:

    jnc and LMS2968 like this.
  11. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    More important to me would have been water level. When you are going up an incline which levels out at the top it is always a case of judging the water level so that the crown isn't uncovered when it hits the level. If you ascend the incline firebox first that problem immediately goes away because the water level over the firebox will increase. You wouldn't set off without sufficient water but when ascending the bank you know that, as long as the water is clinging to the gauge glass by capillary action, you still have sufficient to get you to the top.
     
  12. peckett

    peckett Member

    Joined:
    Sep 26, 2006
    Messages:
    726
    Likes Received:
    549
    Please click on "CLICK TO EXPANED" above my photo's to see my comments.Third time this is happened today,!!
     
  13. LMS2968

    LMS2968 Part of the furniture

    Joined:
    Sep 1, 2006
    Messages:
    2,987
    Likes Received:
    5,084
    Gender:
    Male
    Occupation:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Location:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Which is why most banking duties were done with the chimney at the uphill end and why the Garratt arrived at Bromsgrove that way around. There were exceptions: banking from Bolton towards Blackburn was usually done tender first. In this case it was often a Lanky A Class, which had a very low, open tender, and the rear of the train ahead afforded some protection from the weather on the climb, while the return journey had the spectacle plate in front. Which unfortunately has nothing to do with Garratts . . .
     
    Richard Roper likes this.
  14. Jamessquared

    Jamessquared Nat Pres stalwart

    Joined:
    Mar 8, 2008
    Messages:
    26,101
    Likes Received:
    57,418
    Location:
    LBSC 215
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I think @Steve is actually suggesting the opposite. If you are working on a switchback line (steep uphill --> steep downhill; or steep uphill --> level), working backwards makes control of the water level easier, because at the point the gradient changes and you shut off, the change in levels works in your favour. If you go up chimney leading, the change in gradient works against you and you can suddenly find yourself with low water when you shut off (and made worse if you also brake at the top, as a banker might do).

    Tom
     
    jnc, Richard Roper, Wenlock and 2 others like this.
  15. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Better explained than me, Tom.
     
  16. Cartman

    Cartman Well-Known Member Account Suspended

    Joined:
    Dec 14, 2015
    Messages:
    2,290
    Likes Received:
    1,672
    Gender:
    Male
    Occupation:
    Van driver
    Location:
    Cheshire
    Heritage Railway Volunteer:
    No I do not currently volunteer
    I didn't know that. One thing I did read about the LMS ones is that one was used on a freight across the Peak district line towards Manchester through Dove Holes tunnel and the brake blocks melted on the steep downgrades towards Stockport
     
    Richard Roper likes this.
  17. LMS2968

    LMS2968 Part of the furniture

    Joined:
    Sep 1, 2006
    Messages:
    2,987
    Likes Received:
    5,084
    Gender:
    Male
    Occupation:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Location:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Probably not melted, but it did need reblocking at Manchester, and they didn't do it again!

    There is a photo of 4999 on the train. It was taken by Frank Carrier, an LMS draughtsman, and is now copyright of Kidderminster Railway Museum.
     
  18. Jamessquared

    Jamessquared Nat Pres stalwart

    Joined:
    Mar 8, 2008
    Messages:
    26,101
    Likes Received:
    57,418
    Location:
    LBSC 215
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Never really thought about it before, but I guess on an LMS Garratt, you've got less brake capacity than you would have on, say, two 4F 0-6-0s, due to not having the tenders? So you could pull what two 4Fs would manage uphill, but have less brake capacity down the other side ...

    Tom
     
  19. Cartman

    Cartman Well-Known Member Account Suspended

    Joined:
    Dec 14, 2015
    Messages:
    2,290
    Likes Received:
    1,672
    Gender:
    Male
    Occupation:
    Van driver
    Location:
    Cheshire
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Presumably the same problem with diesels on unfitted freights, which gave rise to the diesel brake tenders
     
  20. LMS2968

    LMS2968 Part of the furniture

    Joined:
    Sep 1, 2006
    Messages:
    2,987
    Likes Received:
    5,084
    Gender:
    Male
    Occupation:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Location:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Indeed. Twelve wheels braked instead of twenty-four. Unfortunately, or possibly not, the driver's comments on reaching Manchester are not recorded.
     
    Richard Roper, Jamessquared and Steve like this.

Share This Page